STM32 STM32F103VCT6 Development Board with 3.2" TFT LCD Module

STM32 STM32F103VCT6 Development Board with 3.2" TFT LCD Module

STM32F103VCT6 Dev. Board with MP3,Ethernet,USB Host

CPU:

STMicroelectronics High-density performance line ARM-based 32-bit MCUwith 256k Flash,48k RAM (on chip 12BitA/D D/A
ARM Cortex-M3 running at up to 72 MHz
Thumb-2 instruction set
72 MHz maximum frequency,1.25 DMIPS/MHz (Dhrystone 2.1)performance at 0 wait state memory access
Single-cycle multiplication and hardware division

support a 2.8" TFT Color LCD module or a 3.2" TFT Color LCD module (Default) , 240*RGB*320 pixels  262k color
support 8-bit/16-bit parallel bus interface
IO control mode, TSC2046 touch panel controller onboard  directly compatible withADS7843 on TFT Color LCD module, Support a SD card interface (SPI mode)
Support a ATMEL DataFlash AT45DBxxxseries device

•     128M or 256M NAND FLASH on board, IO control mode, can replacing more  by yourself, for example: 1Gb2Gb 4Gb and so on.
•     VS1003B MP3 decoder device on board.VS1003 is a single-chip MP3/WMA/MIDI audio decoder andADPCM encoder. It contains a high-performance, proprietary low-powerDSP processor core VS DSP4, working data memory, 5 KiBinstruction RAM and 0.5 KiB data RAM for user applications, serial control and input data interfaces,4 general purpose I/O pins, an UART, as well as a high-quality variable-sample-rate mono ADC and stereo DAC, followed by an earphone amplifier and a common buffer.
•      USB host interface, driver IC is CH376.CH376 is file manage and control IC. Application for MCU read USB disk or SD Card file system.CH376 support USB device and
   

USB host mode, integration USB communications protocol firmware, integration Mass-Storage device protocol firmware, integration FAT12 FAT16 FAT32file manage system, support any USB Storage device (include U disk, USB hard disk, SD Card……)
Support 1.5Mbps Low Speed and 12MbpsFull Speed USB, compatible USB 2.0
Support USB-host interface and USB-device interface, support dynamic switch USB-host and USB-device mode
Support USB device Control Transfers, Interrupt Transfers, Bulk Transfers

    ● A MicroChip ENC28J60 10Mbit Ethernet controller IC , IEEE 802.3 compatible Ethernet controller,Integrated MAC and10BASE-T PHY ,Supports one 10BASE-Tport with automatic polarity detection and correction,Supports Full and Half-Duplex modes,on-board RJ45 connector with build in Ethernet transformer and two status LEDseasy interface to any microcontroller via SPI

    ●  USB device interface (STM32F103VCT6 inside)
   
    ●  CAN communications interface, driver IC is SN65VHD230
   
    ●  RS485 communications interface,driver IC is SP3485
   
    ● Two RS232 interface
 
    ●  SD Card interface (SPI conterll mode)
   
    ●  I2C interface (connect 24LC02EEPROM)
   
    ●  SPI interface (connect AT45DB161Ddata flash)
   
    ● one way ADC adjust input
 
    ● two way ADC socket input
  
    ● one way DAC socket output

    ● one beep,four programmable user LED, one power show LED, one USB show LED, three programmable user key, a five direction jockey, one RESET key
  
    ● support 5V Power Supply and USB Power Supply input

    ● All IO port all the leads, user-friendly expansion of functionality, secondary development

    ● Dimensions: 15cm x 11cm

Part: Introduce for 3.2" TFT LCD Module

8-bit or 16-bit parallel bus interface,8-bit mode use 74HC573 latch low 8-bit (short R7enable 8-bit mode), open R7 is 16-bit mode (default), use high 8-bit operation bus in 8-bit mode low 8-bit float, Support a ATMELDataFlash AT45DBxxx series device, Can directly use AVR,PIC,C51,ARM.STM32 MCUdriver.
 

General Introduce
Resolution:  QVGA 262K 240*RGB*320
Size: 3.2"
Controller: IL9320
Touch Panel: 4-wire
Pin Pitch: 37Pins & 1mm
2.7-3.3V operating voltage
Backlight: 5 LEDs Parallel
RSM1843 touch panel controller onboard  directly compatible with ADS7843
Standard 2.54mm PCB headers for prototyping
Support a SD card interface
 

Interface instruction of 3.2" TFT LCD Module